INP-File: Difference between revisions
Jump to navigation
Jump to search
m (Created page with "Input file for SWMM5.") |
No edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
For the description of the drainage system a regular SWMM5 input file is required. The current version implemented in BlueM.MPC is SWMM 5.0.018. The following standards have to be followed in order to use SWMM5 for BlueM.MPC simulations: | |||
* The last line in the [OPTIONS] sections demands the length of the control step in minutes. | |||
* Time dependent controls of the actuators are induced by control rules. The section [CONTROLS] is therefore compulsory. For every control step within the control horizon a control rule is required. Every rule must begin with the line '''IF SIMULATION TIME >''' as shown in the example below. | |||
<bluem> | |||
[TITLE] | |||
SWMM 5.0.018b | |||
TU Darmstadt | |||
ihwb | |||
Datum: 05.11.2010 | |||
[OPTIONS] | |||
FLOW_UNITS LPS | |||
INFILTRATION CURVE_NUMBER | |||
FLOW_ROUTING DYNWAVE | |||
START_DATE 04/01/2008 | |||
START_TIME 12:00:00 | |||
REPORT_START_DATE 04/01/2008 | |||
REPORT_START_TIME 12:00:00 | |||
END_DATE 04/04/2008 | |||
END_TIME 12:00:00 | |||
SWEEP_START 01/01 | |||
SWEEP_END 12/31 | |||
DRY_DAYS 0 | |||
REPORT_STEP 00:01:00 | |||
WET_STEP 00:01:00 | |||
DRY_STEP 01:00:00 | |||
ROUTING_STEP 0:00:01 | |||
ALLOW_PONDING YES | |||
INERTIAL_DAMPING NONE | |||
VARIABLE_STEP 0.00 | |||
LENGTHENING_STEP 0 | |||
MIN_SURFAREA 0 | |||
NORMAL_FLOW_LIMITED BOTH | |||
SKIP_STEADY_STATE NO | |||
FORCE_MAIN_EQUATION D-W | |||
LINK_OFFSETS DEPTH | |||
MIN_SLOPE 0 | |||
;CONTROL_STEP 00:10:00 | |||
[FILES] | |||
USE INFLOWS "D:\Data\Develop\DevTest\SWMM\M180_MPC\M180Inflow.txt" | |||
USE HOTSTART "D:\Data\Develop\DevTest\SWMM\M180_MPC\M180.hsf" | |||
;SAVE HOTSTART "D:\Data\Develop\DevTest\SWMM\M180_MPC\M180.hsf" | |||
. | |||
. | |||
. | |||
[CONTROLS] | |||
RULE T5 | |||
IF SIMULATION TIME > 1:00 | |||
THEN PUMP B100Pp SETTING = 0.50 | |||
RULE T4 | |||
IF SIMULATION TIME > 0:50 | |||
THEN PUMP B100Pp SETTING = 0.50 | |||
RULE T3 | |||
IF SIMULATION TIME > 0:40 | |||
THEN PUMP B100Pp SETTING = 0.50 | |||
RULE T2 | |||
IF SIMULATION TIME > 0:30 | |||
THEN PUMP B100Pp SETTING = 0.50 | |||
RULE T1 | |||
IF SIMULATION TIME > 0:20 | |||
THEN PUMP B100Pp SETTING = 0.50 | |||
RULE T0 | |||
IF SIMULATION TIME > 0:10 | |||
THEN PUMP B100Pp SETTING = 0.50 | |||
. | |||
. | |||
. | |||
</bluem> | |||
Latest revision as of 05:03, 15 December 2010
For the description of the drainage system a regular SWMM5 input file is required. The current version implemented in BlueM.MPC is SWMM 5.0.018. The following standards have to be followed in order to use SWMM5 for BlueM.MPC simulations:
- The last line in the [OPTIONS] sections demands the length of the control step in minutes.
- Time dependent controls of the actuators are induced by control rules. The section [CONTROLS] is therefore compulsory. For every control step within the control horizon a control rule is required. Every rule must begin with the line IF SIMULATION TIME > as shown in the example below.
[TITLE] SWMM 5.0.018b TU Darmstadt ihwb Datum: 05.11.2010 [OPTIONS] FLOW_UNITS LPS INFILTRATION CURVE_NUMBER FLOW_ROUTING DYNWAVE START_DATE 04/01/2008 START_TIME 12:00:00 REPORT_START_DATE 04/01/2008 REPORT_START_TIME 12:00:00 END_DATE 04/04/2008 END_TIME 12:00:00 SWEEP_START 01/01 SWEEP_END 12/31 DRY_DAYS 0 REPORT_STEP 00:01:00 WET_STEP 00:01:00 DRY_STEP 01:00:00 ROUTING_STEP 0:00:01 ALLOW_PONDING YES INERTIAL_DAMPING NONE VARIABLE_STEP 0.00 LENGTHENING_STEP 0 MIN_SURFAREA 0 NORMAL_FLOW_LIMITED BOTH SKIP_STEADY_STATE NO FORCE_MAIN_EQUATION D-W LINK_OFFSETS DEPTH MIN_SLOPE 0 ;CONTROL_STEP 00:10:00 [FILES] USE INFLOWS "D:\Data\Develop\DevTest\SWMM\M180_MPC\M180Inflow.txt" USE HOTSTART "D:\Data\Develop\DevTest\SWMM\M180_MPC\M180.hsf" ;SAVE HOTSTART "D:\Data\Develop\DevTest\SWMM\M180_MPC\M180.hsf" . . . [CONTROLS] RULE T5 IF SIMULATION TIME > 1:00 THEN PUMP B100Pp SETTING = 0.50 RULE T4 IF SIMULATION TIME > 0:50 THEN PUMP B100Pp SETTING = 0.50 RULE T3 IF SIMULATION TIME > 0:40 THEN PUMP B100Pp SETTING = 0.50 RULE T2 IF SIMULATION TIME > 0:30 THEN PUMP B100Pp SETTING = 0.50 RULE T1 IF SIMULATION TIME > 0:20 THEN PUMP B100Pp SETTING = 0.50 RULE T0 IF SIMULATION TIME > 0:10 THEN PUMP B100Pp SETTING = 0.50 . . .